XLB-S12T Double head blowing Locking Screw Machine

Equipment introduction

Xlb-s12t double head air blowing automatic screwing machine is also called blowing head automatic screw locking machine and blowing head automatic screw tightening machine. It is commonly used for automatic processing in electronics, toys, hardware and other industries.

Equipment use

This equipment is a general-purpose automatic screw locking machine, which can lock screws according to different product programming. To replace products, you only need to replace fixtures, and to replace screws, you need to replace screw suppliers.

Main technical parameters of equipment

equipment installation

During equipment installation, pay attention to adjusting the height of each foot to keep the equipment horizontal and stable. The installation site shall pay attention to the necessary space for equipment operation, maintenance and repair.

Function introduction of automatic screw locking machine

1: Full Chinese interface, dynamic display of operation status, intuitive and visible parameter units.

2: Password protection function to protect system parameters from being changed at will.

3: Program single correction and overall correction function, which greatly saves the time of manual programming.

4: Single step, automatic positioning function, which greatly facilitates the production, confirmation and coordinate repair of programs.

5: Store 100 models, and each model can make a 16 step program! When in use, you can switch and call at will.

6: External SD memory card can be exchanged between devices, saving the time of reprogramming.

7: High efficiency, labor saving and cost saving.

Operation preparation

1: Please turn on the main power switch.

2: Observe whether the air pressure is sufficient.

3: Please press the operation preparation button.

4: The servo motor is reset (automatic), so as to ensure the walking accuracy.

Manual operation

Manually put the product into the fixture, and then press the start key to start the automatic locking of the screw. After the locking is completed, go to the reclaiming position, take out the product by the personnel at the lower station, and the fixture can return to the discharging position.

Automatic operation

Manually put the product into the fixture, press the start key to start locking. After the locking is completed to the reclaiming position, the personnel at the lower station take the product, the fixture returns to the discharging position, and then put the next product. At this time, it is not necessary to press the start key, and the machine automatically starts locking.

Alarm release description

1: In case of abnormality, please press the "emergency stop" button.

2: Please press the "reset" button.

3: Automatic reset of motor and cylinder.

4: After confirming that they are in the original position, restart.

Safe operation instructions

1: After starting the step switch, do not reach into the range of the machine.

2: Do not touch the touch screen and keys if there is no abnormality during the operation of the machine.

3: Do not press any button or switch other than emergency stop.

4: Please turn off the power when you are not using the machine.

Equipment maintenance

1: Clean the filter screen of vacuum generator regularly; It is recommended to clean once a month.

2: Clean the vacuum suction nozzle of the electric batch regularly; It is recommended to clean once a week.

3: Regularly clean the dust of screw feeder and add lubricating oil; It is recommended to clean once a month.

4: Clean the dust of the equipment regularly and add lubricating oil to the motion module; It is recommended to clean once a month.

5: Regularly check whether the connecting screws of the equipment are loose and tight. It is recommended to check once a month.

matters needing attention

1: Please use the correct voltage. The error range of input voltage should be within ± 10V, and ensure that the machine should be properly grounded to prevent injury caused by electric leakage of the machine.

2: When making any adjustment to the machine, be sure to turn off the power and air supply first, and unplug the plug to maintain safety. Non operators should approach to avoid danger.

3: Clean the equipment regularly, and remember to perform this action when the gas and power are off.

4: Check whether the torque of the electric screwdriver is suitable for the current torque range of the locking screw, and retest the torque with a torque meter.

Common faults and troubleshooting

1: The screw cannot be absorbed or the screw is not locked

--Check whether the screw feeder sends screws, and take the screws by hand to see if they work normally

--Check whether the vacuum is weakened, open the sheet metal of the x-axis rear cover, and take out the vacuum generator for cleaning

--Check whether the screw suction position is offset, enter "other settings" to reset the suction position

--Observe whether the screw sensor light is on. If any screw is not on, it indicates abnormal sensing

2: Product screw lock with sliding teeth

1) : check whether the torque of the electric screwdriver is suitable for the current torque range of the locking screw, and retest the torque with a torque meter

2) : check whether the locking speed is too small, and appropriately increase the trial lock to observe its locking effect.

3) : observe whether the locking position is too small, and appropriately increase the locking position of the current step for trial locking.

3: Screw lock attached floating height

Check whether the locking height set in step of the procedure reaches the actual locking position of the screw and whether the parameter setting of locking speed is correct.

4: The position of the locking screw is offset.

Check whether the position of each coordinate point in the program is accurate, select the coordinate correction function and re calibrate the coordinates

5: Device crash

--Check whether the program parameters are set correctly, and restart the equipment after confirmation

--Check whether the power supply is abnormal.